Symmons 86-2X-BODY Manuel d'instructions télécharger pdf

Tub-Shower Mixing Valves 86-1X-BODY-IPS, 86-2X-BODY-IPS

Installation Brief

1 2 3 4

Pipe

Sealant

Plumbers

Putty

Tools & Materials

 Need Help?

Contact Symmons customer service

at (800) 796-6667, (781) 848-2250,

[email protected]

Mon - Fri 7:30 am - 7:00 pm EST

 Please check Symmons website

for technical help, the latest product

information and warranty policy.

www.symmons.com/service

Model number

86-1X-BODY-IPS

Temptrol Tub-Shower mixing valve

86-2X-BODY-IPS

Temptrol Shower mixing valve

Temptrol

™

Figure 1 Mounting plate

(valve without IPS ports shown)

p/n T-176

p/n T-177

Protective shield

When mounting plate is used,

then shield is optional for

protecting end of valve during

installation.

"snap on-off"

wall cutout hole size

3-1/2" (89 mm) min

4" (102 mm) max

nished

wall

Ensure valve’s

mounting plate

is ush against

inner wall

Walls for using T-177 valve mounting plate

 Fiberglass or acrylic walls (required)



Plaster or other type walls (optional)

1/16" (2 mm) min  1/2" (13 mm) max

wall cutout hole size

3-1/2" (89 mm) min

4" (102 mm) max

Finished wall must be

ush with back side of

protective shield surface

nished wall

Dry wall, plaster or other type wall

1/2" (13 mm) or greater

Protective shield

"snap on-off"

(required when

valve mounting

plate is not used)

Reference rough-in

dimensional

drawing on page 2

Figure 2 Mounting valve (valve without IPS ports shown)

Rough-in Installation

Installing control valve, piping & fittings

Reference rough-in dimension illustration

on page 2 as required.

1) Determine wall thickness

■

Determine type of wall and wall

thickness where valve will be mounted.

■ Consider whether to use mounting plate

by reviewing gure 2 below.

■ Skip ahead to Step 3 if mounting

plate will not be used.

2) Attach mounting plate to valve

Seat mounting plate against valve

assembly as illustrated in gure 1.

3) Attach protective shield

■ Reference gure 2 to determine

whether shield is required.

■ Attach plastic protective shield by

snap tting over end of valve spindle.

4) Install piping, ﬁttings and

control valve

Piping and ttings not supplied

■ Control Valve

Install valve through cutout hole in

wall as specied in gure 2 below and

dimension illustration on page 2.

■ Showerhead (S on valve)

Pipe from outlet port on valve marked S

to showerhead mounting arm location.

■ Hot & Cold Supply (H & C)

Pipe hot water supply to valve input

marked H and cold water supply to

valve input marked C.

■ Tub Spout (T on valve)

Pipe from outlet port on valve marked

T to tub spout. (86-2X-BODY-IPS)

1 2 3 4

Résumé du contenu

Page 1 - Temptrol

Tub-Shower Mixing Valves 86-1X-BODY-IPS, 86-2X-BODY-IPSInstallation Brief1 2 3 4PipeSealantPlumbersPuttyTools & Materials Need Hel

Page 2 - 86-1X-BODY-IPS

Page 2 Tighten packing nut for positive frictional resistance as handle is rotated from shuto position across adjustment range. 7) Flush system an

Page 3 - Parts Assembly

Page 3Cap washer repair kit(T-16)Service stop assy & retainer (T-52)hot washer screwhot washercold washer retainercold washer cap gasket Control s

Page 4 - Trouble Shooting Chart

If piston appears restricted then do the following:(1) Tap the handle or stem end of the spindle against a solid object to free the piston.(2) Try

Commentaires sur ces manuels

Pas de commentaire

Symmons 86-2X-BODY Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Articles sanitaires Symmons 86-2X-BODY. Symmons 86-2X-BODY Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Articles sanitaires Symmons 86-2X-BODY